Commit 55e7064b authored by remi.clement's avatar remi.clement
Browse files

update

Showing with 102 additions and 10 deletions
+102 -10
File added
File added
PCB_file_measurement card/card_measure_raspberry_v3.04_schéma.png

232 KB

No preview for this file type
No preview for this file type
No preview for this file type
No preview for this file type
......@@ -44,9 +44,9 @@ OS installation
The first step is to start up the Raspberry Pi board, including installation of an OS (operating system).
For this step, the installation instructions are well described on the Raspberry website
1- Watch the vidéo "how to set up your raspberry Pi" (https://www.youtube.com/watch?v=wjWZhV1v3Pk)
1. Watch the vidéo "how to set up your raspberry Pi" (https://www.youtube.com/watch?v=wjWZhV1v3Pk)
2- The authors recommend installing the latest stable and complete version of Raspbian by using NOOBS (a simple-to-use operating system installer).
2. The authors recommend installing the latest stable and complete version of Raspbian by using NOOBS (a simple-to-use operating system installer).
.. note::
All the development tests were performed on Raspberry Pi 3 Model B, we used the following version of Raspbian:
......@@ -61,7 +61,37 @@ For this step, the installation instructions are well described on the Raspberry
.. warning::
Once the OS has been installed, the 1-wire option and GPIO remote option must be deactivated via the Raspbian GUI settings menu. Failure to carry out this task may cause damage to the relay shield cards during measurements.
Once the OS has been installed, **1-wire, spi and GPIO remote option** must be deactivated via the Raspbian GUI settings menu. Failure to carry out this task may cause damage to the relay shield cards during measurements.
3. When the relays are connected to the GPIO, make sure that all the GPIOs are in the low position when the raspberry starts up. If not, the relays will activate unexpectedly.
To ensure that the GPIOs are in Low position, you will need to modify the /boot/config.txt file.
Run the terminal, and write
.. code-block:: python
cd /boot/
4. Open config.txt with GNU nano editor
.. code-block:: python
sudo nano config.txt
5. At the end of the file write :
.. code-block:: python
gpio=8=op,dl
gpio=7=op,dl
6. Press Ctrl +O to save the modifications and press enter
7. Press Ctrl +x to escap and return to the terminal
8. Close the terminal
Virtual Environnement and packages
......
......@@ -159,7 +159,7 @@
<dd class="field-odd"><p>open hardware resistivity-meter</p>
</dd>
<dt class="field-even">Date</dt>
<dd class="field-even"><p>Nov 27, 2020</p>
<dd class="field-even"><p>Dec 11, 2020</p>
</dd>
<dt class="field-odd">Authors</dt>
<dd class="field-odd"><p><strong>Rémi CLEMENT, Nicolas FORQUET, Julien GANCE, Yannick FARGIER, Vivien DUBOIS, Hélène GUYARD</strong></p>
......
......@@ -249,8 +249,10 @@ control system</p></td>
<h3>OS installation<a class="headerlink" href="#os-installation" title="Permalink to this headline"></a></h3>
<p>The first step is to start up the Raspberry Pi board, including installation of an OS (operating system).
For this step, the installation instructions are well described on the Raspberry website</p>
<p>1- Watch the vidéo “how to set up your raspberry Pi” (<a class="reference external" href="https://www.youtube.com/watch?v=wjWZhV1v3Pk">https://www.youtube.com/watch?v=wjWZhV1v3Pk</a>)</p>
<p>2- The authors recommend installing the latest stable and complete version of Raspbian by using NOOBS (a simple-to-use operating system installer).</p>
<ol class="arabic simple">
<li><p>Watch the vidéo “how to set up your raspberry Pi” (<a class="reference external" href="https://www.youtube.com/watch?v=wjWZhV1v3Pk">https://www.youtube.com/watch?v=wjWZhV1v3Pk</a>)</p></li>
<li><p>The authors recommend installing the latest stable and complete version of Raspbian by using NOOBS (a simple-to-use operating system installer).</p></li>
</ol>
<div class="admonition note">
<p class="admonition-title">Note</p>
<p>All the development tests were performed on Raspberry Pi 3 Model B, we used the following version of Raspbian:</p>
......@@ -260,8 +262,38 @@ For this step, the installation instructions are well described on the Raspberry
</div>
<div class="admonition warning">
<p class="admonition-title">Warning</p>
<p>Once the OS has been installed, the 1-wire option and GPIO remote option must be deactivated via the Raspbian GUI settings menu. Failure to carry out this task may cause damage to the relay shield cards during measurements.</p>
<p>Once the OS has been installed, <strong>1-wire, spi and GPIO remote option</strong> must be deactivated via the Raspbian GUI settings menu. Failure to carry out this task may cause damage to the relay shield cards during measurements.</p>
</div>
<p>3. When the relays are connected to the GPIO, make sure that all the GPIOs are in the low position when the raspberry starts up. If not, the relays will activate unexpectedly.
To ensure that the GPIOs are in Low position, you will need to modify the /boot/config.txt file.</p>
<blockquote>
<div><p>Run the terminal, and write</p>
<div class="highlight-python notranslate"><div class="highlight"><pre><span></span><span class="n">cd</span> <span class="o">/</span><span class="n">boot</span><span class="o">/</span>
</pre></div>
</div>
</div></blockquote>
<ol class="arabic simple" start="4">
<li><p>Open config.txt with GNU nano editor</p></li>
</ol>
<blockquote>
<div><div class="highlight-python notranslate"><div class="highlight"><pre><span></span><span class="n">sudo</span> <span class="n">nano</span> <span class="n">config</span><span class="o">.</span><span class="n">txt</span>
</pre></div>
</div>
</div></blockquote>
<ol class="arabic simple" start="5">
<li><p>At the end of the file write :</p></li>
</ol>
<blockquote>
<div><div class="highlight-python notranslate"><div class="highlight"><pre><span></span><span class="n">gpio</span><span class="o">=</span><span class="mi">8</span><span class="o">=</span><span class="n">op</span><span class="p">,</span><span class="n">dl</span>
<span class="n">gpio</span><span class="o">=</span><span class="mi">7</span><span class="o">=</span><span class="n">op</span><span class="p">,</span><span class="n">dl</span>
</pre></div>
</div>
</div></blockquote>
<ol class="arabic simple" start="6">
<li><p>Press Ctrl +O to save the modifications and press enter</p></li>
<li><p>Press Ctrl +x to escap and return to the terminal</p></li>
<li><p>Close the terminal</p></li>
</ol>
</div>
<div class="section" id="virtual-environnement-and-packages">
<h3>Virtual Environnement and packages<a class="headerlink" href="#virtual-environnement-and-packages" title="Permalink to this headline"></a></h3>
......
Search.setIndex({docnames:["index","page0","page1"],envversion:{"sphinx.domains.c":2,"sphinx.domains.changeset":1,"sphinx.domains.citation":1,"sphinx.domains.cpp":3,"sphinx.domains.index":1,"sphinx.domains.javascript":2,"sphinx.domains.math":2,"sphinx.domains.python":2,"sphinx.domains.rst":2,"sphinx.domains.std":1,sphinx:56},filenames:["index.rst","page0.rst","page1.rst"],objects:{},objnames:{},objtypes:{},terms:{"400px":[],"800px":[],"ao\u00fbt":1,"case":2,"cr\u00e9er":[],"d\u00e9mo":[],"esp\u00e8r":[],"final":2,"function":[1,2],"h\u00e9l\u00e8ne":[0,1],"install\u00e9":[],"justifi\u00e9":[],"mm\u00b2":2,"nec\u00e9ssair":[],"new":2,"orl\u00e9an":1,"pr\u00e9sent":[],"pr\u00e9sentat":[],"premi\u00e8r":[],"r\u00e9mi":[0,1],"r\u00e9sistanc":[],"switch":2,"universit\u00e9":1,"vid\u00e9o":2,ADS:2,For:2,IDE:[],IGE:1,Its:2,The:0,These:2,With:2,abmn:2,abov:2,acc:2,access:2,accord:2,accur:2,accuraci:2,acid:2,activ:[],actual:2,adafruit:2,adapt:2,adc:2,added:2,adding:2,addit:2,address:2,adjust:2,administr:[],ads1115:2,ads115:2,ads1x15:2,after:2,align:[],all:2,allow:[1,2],alp:1,also:2,alt:[],altern:2,amplifi:2,analog:2,ani:2,anoth:2,appear:2,appli:2,apt:2,arrai:2,articl:[],assembl:0,assist:2,associ:1,attent:2,attribut:2,aug:[],author:[0,1,2],automat:[1,2],automobil:2,avail:2,avon:[],bank:2,barbeau:[],base:2,basic:1,batteri:2,been:2,befor:2,behavior:2,being:2,below:2,between:2,bin:2,bit:2,black:2,blinka:2,block:2,blue:2,bluetext:[],board:[],bodytext:[],both:2,bridg:2,button:2,c_1:[],c_2:[],cabl:2,calcul:2,calibr:2,call:1,can:2,cap:2,capac:2,caption:[],card:0,carri:2,caus:2,ceci:[],cedex:1,cela:[],center:[],chacun:[],channel:2,characterist:2,charg:2,check:2,chosen:2,christoph:[],circuit:2,circuitpython:2,circul:2,clean:2,clement:[0,1],click:2,close:2,code:2,coef_p0:2,coef_p1:2,coef_p2:2,coef_p3:2,coeff:2,coeff_:[],coeff_p0:[],coeff_p1:[],coeff_p3:[],coeff_p_:[],coeffici:2,cokela:[],com:2,command:2,commerci:2,common:2,commun:1,complet:2,compon:2,comput:2,conduct:2,configur:0,connect:0,connector:2,consequ:2,consist:2,constitut:2,construct:2,consult:[],consumpt:2,contact:2,contain:2,content:0,control:2,convers:2,convert:2,correct:2,corrig:[],cos:[],cost:1,could:2,cpu:2,creat:2,creation:1,csv:2,current:[0,1],damag:2,dan:[],daniel:[],data:0,date:[0,1],deactiv:2,decid:2,delai:2,deliv:2,demo:[],depend:2,des:[],describ:2,design:2,despit:2,dev:2,develop:[0,1,2],developp:[],diagram:2,differ:2,digit:2,din:2,direct:2,directli:2,directori:2,disconnect:2,displai:2,distanc:2,disturb:2,divid:2,diviseur:[],dkfjshkdfh:[],doc:[],document:1,done:2,download:2,dual:2,duboi:[0,1],durat:2,dure:2,dzwb4:2,each:2,eiffel:1,either:2,electr:[],electrod:[0,1],electron:2,enabl:2,end:2,energ:2,enough:2,ensur:2,entir:2,environ:2,environn:[],environnementshould:2,equal:2,equival:2,eric:[],ert:2,est:[],estim:2,everyon:1,exampl:2,excess:2,execut:2,experi:[1,2],extra:2,failur:2,fair:[],fargier:[0,1],featur:[],femal:2,fewer:2,field:2,fig:2,figclass:[],figur:2,file:2,find:2,first:2,flexibl:1,florsch:2,flow:2,folder:2,follow:2,fonctionn:[],formul:[],forquet:[0,1],four:[],framework:2,franc:1,from:2,full:2,fulli:1,fuse:2,gain:2,ganc:[0,1],gather:2,gener:[0,2],ger:1,get:[1,2],gitlab:2,gpio:2,grenobl:1,ground:2,gui:2,guidelin:0,gustav:1,guyard:[0,1],had:2,hand:2,handl:2,hardwar:[1,2],hardwareresist:[],has:2,have:2,hazard:2,header:2,hear:2,height:[],help:[],high:2,holder:2,hole:2,home:2,horizont:2,hous:2,how:2,howev:2,http:2,ifsttar:1,illustr:2,imag:[],imped:2,implement:[],implent:0,inastal:[],includ:2,incom:2,increas:2,inde:2,index:[],inform:[],inject:[0,1],injection_dur:2,input:2,inra:1,insert:2,insid:2,instal:[],instead:2,instruct:0,instrument:1,intens:2,interfac:2,interpret:2,introduc:2,introduct:0,introduir:[],invit:[],involv:1,ion:2,iri:1,irstea:2,jpg:[],juillet:1,julien:[0,1],justifi:[],keyboard:2,kjsdfhksdgfjksdf:[],known:2,kohm:2,laboratori:2,lastli:2,latest:2,lead:2,leav:2,length:2,les:[],less:2,let:2,libatla:2,librari:2,lie:2,lien:[],like:[],limit:0,line:2,lineno:[],list:2,lithium:2,lm358n:2,locat:2,logger:2,logo:[],logo_inra:[],logo_univ_gustav:[],low:[1,2],lying:2,lyon:1,made:2,mai:2,main:2,make:2,manag:2,manual:2,manuscript:2,massembl:[],master:2,mathrm:[],matur:0,maxdepth:[],maximum:2,measur:[0,1],mechan:2,meet:2,mega:2,menu:2,met:2,meter:[1,2],meterfeatur:1,micro:2,mimic:2,min:2,model:2,modif:2,modifi:2,modul:2,mohm:2,monitor:2,moreov:2,moscardi:[],mount:2,mous:2,multi:2,multiplex:[0,1],multipli:2,must:2,mux:2,n_k:[],name:2,nb_electrod:2,nbr_mea:2,necessari:2,need:2,neg:2,next:2,nicola:[0,1],noob:2,normal:2,note:2,notr:[],nou:[],nov:0,now:2,number:2,numer:2,numpi:2,obtain:2,offcial:0,offer:2,officiel:[],offset:[],ohm:2,ohmmet:2,ohmpi:[],onc:2,one:2,onli:[],onto:2,open:[1,2],oper:0,optim:2,option:2,order:2,org:[],osf:2,other:2,our:2,out:2,output:2,ouvr:[],packag:[],page0:[],page1:[],page:[],pai:2,panda:2,paramet:[],parent:[],parl:[],part:2,parten:1,path:2,pcb:2,per:2,perform:[1,2],permut:2,peu:[],philosophi:[0,1],pin1:[],pin:2,pip:2,pitch:2,place:2,pleas:2,plu:[],plug:2,png:[],point:2,polar:2,pole:2,pond:[],posit:2,possibl:2,potenti:2,pour:[],power:2,practic:2,pradal:[],precis:2,prefer:2,prepar:2,present:[1,2],previous:2,print:2,procedur:[],produc:2,program:2,progress:[0,1],project:0,propos:2,protocol:2,provid:[1,2],puls:2,purpos:2,pyhton3:2,python3:2,python:[],pythonid:2,quadripol:2,quadrupol:2,que:[],r10:2,r11:2,r12:2,r_ref:2,rail:2,rang:2,rapberri:[],raspberri:0,raspberrypi:[],raspbian:2,raspbian_vers:[],raspebrri:2,readm:2,recommend:2,red:[],reduct:2,refer:2,relai:2,relat:[],releas:0,remain:2,rememb:2,remot:2,repeat:2,repetit:2,repositori:2,repres:2,requir:2,research:0,resist:[0,1],resistor:2,resolut:2,respect:2,result:2,revers:2,reversa:[1,2],robust:[1,2],role:2,root:2,rpi:2,rro:1,run:2,s_k:[],safeti:2,same:2,save:2,scale:1,schemat:2,scienc:2,scientif:1,screen:2,screw:2,search:[],second:2,section:2,see:2,select:2,sequenc:2,sequence_delai:2,seri:2,serv:2,set:2,setup:2,sever:2,shield:2,shortcut:2,should:2,show:2,shown:2,signal:2,simpl:2,simpli:2,simultan:2,singl:2,site:[],slope:2,small:[1,2],smaller:2,softwar:2,soil:2,solder:2,solut:2,some:[0,2],sound:2,sourc:[1,2],specif:2,specifi:2,sphinx:[],stabl:2,stack:2,stainless:2,start:2,statu:[0,1],steel:2,step:2,still:2,storag:2,strip:2,strong:2,stronger:2,strongli:2,stuck:2,studi:2,style:[],subject:2,sudo:2,suffici:2,suggest:2,suitabl:2,sum:2,sum_:[],suppli:2,sur:[],surfac:1,system:2,tab:2,tabl:2,target:0,task:2,technic:0,temperatur:2,ten:2,termin:2,test:2,tester:[],text:[],textcolor:[],than:2,thei:2,therefor:2,thi:[1,2],thoma:[],thonni:[],thousand:2,three:2,through:2,thu:2,time:2,toctre:[],togeth:2,tool:1,total:2,tourn:[],track:2,turn:2,tutori:0,two:2,txt:2,type:2,typic:2,under:2,underconstruct:[],unit:2,univ:1,unzip:2,updat:1,upping:2,use:2,used:2,user:[0,2],using:2,usr:2,valeur:[],valu:2,variou:2,venv:2,version:2,vertic:2,via:2,villeurbann:1,virtual:[],vise:[],vivien:[0,1],vlide:2,voi:[],voici:[],voltag:2,voltmet:2,vou:[],wai:2,watch:2,weaker:2,websit:2,welcom:1,well:2,were:2,when:2,where:2,which:2,whose:2,width:[],willing:1,window:2,wire:2,within:2,without:2,wjwzhv1v3pk:2,would:2,www:2,x_n:[],yannick:[0,1],you:2,your:2,youtub:2},titles:["OHMPI: Open source and open hardware resitivity-meter","<strong>OhmPi project</strong>","OhmPi V 1.01 (limited to 32 electrodes)"],titleterms:{IDE:2,The:2,activ:2,assembl:2,bienvenu:[],board:2,card:2,center:0,cett:[],configur:2,connect:2,construct:[],current:2,data:2,descript:2,developp:[],document:0,electr:2,electrod:2,environn:2,formul:[],four:2,frist:2,hardwar:0,imag:[],implement:2,implent:2,inastal:[],indic:[],initi:2,inject:2,instal:2,instruct:2,introduct:1,lien:[],limit:2,massembl:[],measur:2,mesur:2,meter:0,modif:[],multiplex:2,ohmpi:[0,1,2],onli:2,open:0,openalea:[],oper:2,packag:2,page:[],paramet:2,philosophi:2,preliminari:2,procedur:2,project:1,python:2,rapberri:2,raspberri:2,resist:2,resit:0,run:[],second:[],sourc:0,startup:2,step:[],summari:0,sur:[],tabl:[],technic:2,text:[],thonni:2,virtual:2,welcom:[]}})
\ No newline at end of file
Search.setIndex({docnames:["index","page0","page1"],envversion:{"sphinx.domains.c":2,"sphinx.domains.changeset":1,"sphinx.domains.citation":1,"sphinx.domains.cpp":3,"sphinx.domains.index":1,"sphinx.domains.javascript":2,"sphinx.domains.math":2,"sphinx.domains.python":2,"sphinx.domains.rst":2,"sphinx.domains.std":1,sphinx:56},filenames:["index.rst","page0.rst","page1.rst"],objects:{},objnames:{},objtypes:{},terms:{"400px":[],"800px":[],"ao\u00fbt":1,"case":2,"cr\u00e9er":[],"d\u00e9mo":[],"esp\u00e8r":[],"final":2,"function":[1,2],"h\u00e9l\u00e8ne":[0,1],"install\u00e9":[],"justifi\u00e9":[],"mm\u00b2":2,"nec\u00e9ssair":[],"new":2,"orl\u00e9an":1,"pr\u00e9sent":[],"pr\u00e9sentat":[],"premi\u00e8r":[],"r\u00e9mi":[0,1],"r\u00e9sistanc":[],"return":2,"switch":2,"universit\u00e9":1,"vid\u00e9o":2,ADS:2,For:2,IDE:[],IGE:1,Its:2,The:0,These:2,With:2,abmn:2,abov:2,acc:2,access:2,accord:2,accur:2,accuraci:2,acid:2,activ:[],actual:2,adafruit:2,adapt:2,adc:2,added:2,adding:2,addit:2,address:2,adjust:2,administr:[],ads1115:2,ads115:2,ads1x15:2,after:2,align:[],all:2,allow:[1,2],alp:1,also:2,alt:[],altern:2,amplifi:2,analog:2,ani:2,anoth:2,appear:2,appli:2,apt:2,arrai:2,articl:[],assembl:0,assist:2,associ:1,attent:2,attribut:2,aug:[],author:[0,1,2],automat:[1,2],automobil:2,avail:2,avon:[],bank:2,barbeau:[],base:2,basic:1,batteri:2,been:2,befor:2,behavior:2,being:2,below:2,between:2,bin:2,bit:2,black:2,blinka:2,block:2,blue:2,bluetext:[],board:[],bodytext:[],boot:2,both:2,bridg:2,button:2,c_1:[],c_2:[],cabl:2,calcul:2,calibr:2,call:1,can:2,cap:2,capac:2,caption:[],card:0,carri:2,caus:2,ceci:[],cedex:1,cela:[],center:[],chacun:[],channel:2,characterist:2,charg:2,check:2,chosen:2,christoph:[],circuit:2,circuitpython:2,circul:2,clean:2,clement:[0,1],click:2,close:2,code:2,coef_p0:2,coef_p1:2,coef_p2:2,coef_p3:2,coeff:2,coeff_:[],coeff_p0:[],coeff_p1:[],coeff_p3:[],coeff_p_:[],coeffici:2,cokela:[],com:2,command:2,commerci:2,common:2,commun:1,complet:2,compon:2,comput:2,conduct:2,config:2,configur:0,connect:0,connector:2,consequ:2,consist:2,constitut:2,construct:2,consult:[],consumpt:2,contact:2,contain:2,content:0,control:2,convers:2,convert:2,correct:2,corrig:[],cos:[],cost:1,could:2,cpu:2,creat:2,creation:1,csv:2,ctrl:2,current:[0,1],damag:2,dan:[],daniel:[],data:0,date:[0,1],deactiv:2,dec:0,decid:2,delai:2,deliv:2,demo:[],depend:2,des:[],describ:2,design:2,despit:2,dev:2,develop:[0,1,2],developp:[],diagram:2,differ:2,digit:2,din:2,direct:2,directli:2,directori:2,disconnect:2,displai:2,distanc:2,disturb:2,divid:2,diviseur:[],dkfjshkdfh:[],doc:[],document:1,done:2,download:2,dual:2,duboi:[0,1],durat:2,dure:2,dzwb4:2,each:2,editor:2,eiffel:1,either:2,electr:[],electrod:[0,1],electron:2,enabl:2,end:2,energ:2,enough:2,ensur:2,enter:2,entir:2,environ:2,environn:[],environnementshould:2,equal:2,equival:2,eric:[],ert:2,escap:2,est:[],estim:2,everyon:1,exampl:2,excess:2,execut:2,experi:[1,2],extra:2,failur:2,fair:[],fargier:[0,1],featur:[],femal:2,fewer:2,field:2,fig:2,figclass:[],figur:2,file:2,find:2,first:2,flexibl:1,florsch:2,flow:2,folder:2,follow:2,fonctionn:[],formul:[],forquet:[0,1],four:[],framework:2,franc:1,from:2,full:2,fulli:1,fuse:2,gain:2,ganc:[0,1],gather:2,gener:[0,2],ger:1,get:[1,2],gitlab:2,gnu:2,gpio:2,grenobl:1,ground:2,gui:2,guidelin:0,gustav:1,guyard:[0,1],had:2,hand:2,handl:2,hardwar:[1,2],hardwareresist:[],has:2,have:2,hazard:2,header:2,hear:2,height:[],help:[],high:2,holder:2,hole:2,home:2,horizont:2,hous:2,how:2,howev:2,http:2,ifsttar:1,illustr:2,imag:[],imped:2,implement:[],implent:0,inastal:[],includ:2,incom:2,increas:2,inde:2,index:[],inform:[],inject:[0,1],injection_dur:2,input:2,inra:1,insert:2,insid:2,instal:[],instead:2,instruct:0,instrument:1,intens:2,interfac:2,interpret:2,introduc:2,introduct:0,introduir:[],invit:[],involv:1,ion:2,iri:1,irstea:2,jpg:[],juillet:1,julien:[0,1],justifi:[],keyboard:2,kjsdfhksdgfjksdf:[],known:2,kohm:2,laboratori:2,lastli:2,latest:2,lead:2,leav:2,length:2,les:[],less:2,let:2,libatla:2,librari:2,lie:2,lien:[],like:[],limit:0,line:2,lineno:[],list:2,lithium:2,lm358n:2,locat:2,logger:2,logo:[],logo_inra:[],logo_univ_gustav:[],low:[1,2],lying:2,lyon:1,made:2,mai:2,main:2,make:2,manag:2,manual:2,manuscript:2,massembl:[],master:2,mathrm:[],matur:0,maxdepth:[],maximum:2,measur:[0,1],mechan:2,meet:2,mega:2,menu:2,met:2,meter:[1,2],meterfeatur:1,micro:2,mimic:2,min:2,model:2,modif:2,modifi:2,modul:2,mohm:2,monitor:2,moreov:2,moscardi:[],mount:2,mous:2,multi:2,multiplex:[0,1],multipli:2,must:2,mux:2,n_k:[],name:2,nano:2,nb_electrod:2,nbr_mea:2,necessari:2,need:2,neg:2,next:2,nicola:[0,1],noob:2,normal:2,note:2,notr:[],nou:[],nov:[],now:2,number:2,numer:2,numpi:2,obtain:2,offcial:0,offer:2,officiel:[],offset:[],ohm:2,ohmmet:2,ohmpi:[],onc:2,one:2,onli:[],onto:2,open:[1,2],oper:0,optim:2,option:2,order:2,org:[],osf:2,other:2,our:2,out:2,output:2,ouvr:[],packag:[],page0:[],page1:[],page:[],pai:2,panda:2,paramet:[],parent:[],parl:[],part:2,parten:1,path:2,pcb:2,per:2,perform:[1,2],permut:2,peu:[],philosophi:[0,1],pin1:[],pin:2,pip:2,pitch:2,place:2,pleas:2,plu:[],plug:2,png:[],point:2,polar:2,pole:2,pond:[],posit:2,possibl:2,potenti:2,pour:[],power:2,practic:2,pradal:[],precis:2,prefer:2,prepar:2,present:[1,2],press:2,previous:2,print:2,procedur:[],produc:2,program:2,progress:[0,1],project:0,propos:2,protocol:2,provid:[1,2],puls:2,purpos:2,pyhton3:2,python3:2,python:[],pythonid:2,quadripol:2,quadrupol:2,que:[],r10:2,r11:2,r12:2,r_ref:2,rail:2,rang:2,rapberri:[],raspberri:0,raspberrypi:[],raspbian:2,raspbian_vers:[],raspebrri:2,readm:2,recommend:2,red:[],reduct:2,refer:2,relai:2,relat:[],releas:0,remain:2,rememb:2,remot:2,repeat:2,repetit:2,repositori:2,repres:2,requir:2,research:0,resist:[0,1],resistor:2,resolut:2,respect:2,result:2,revers:2,reversa:[1,2],robust:[1,2],role:2,root:2,rpi:2,rro:1,run:2,s_k:[],safeti:2,same:2,save:2,scale:1,schemat:2,scienc:2,scientif:1,screen:2,screw:2,search:[],second:2,section:2,see:2,select:2,sequenc:2,sequence_delai:2,seri:2,serv:2,set:2,setup:2,sever:2,shield:2,shortcut:2,should:2,show:2,shown:2,signal:2,simpl:2,simpli:2,simultan:2,singl:2,site:[],slope:2,small:[1,2],smaller:2,softwar:2,soil:2,solder:2,solut:2,some:[0,2],sound:2,sourc:[1,2],specif:2,specifi:2,sphinx:[],spi:2,stabl:2,stack:2,stainless:2,start:2,statu:[0,1],steel:2,step:2,still:2,storag:2,strip:2,strong:2,stronger:2,strongli:2,stuck:2,studi:2,style:[],subject:2,sudo:2,suffici:2,suggest:2,suitabl:2,sum:2,sum_:[],suppli:2,sur:[],sure:2,surfac:1,system:2,tab:2,tabl:2,tape:[],target:0,task:2,technic:0,temperatur:2,ten:2,termin:2,test:2,tester:[],text:[],textcolor:[],than:2,thei:2,therefor:2,thi:[1,2],thoma:[],thonni:[],thousand:2,three:2,through:2,thu:2,time:2,toctre:[],togeth:2,tool:1,total:2,tourn:[],track:2,turn:2,tutori:0,two:2,txt:2,type:2,typic:2,under:2,underconstruct:[],unexpectedli:2,unit:2,univ:1,unzip:2,updat:1,upping:2,use:2,used:2,user:[0,2],using:2,usr:2,valeur:[],valu:2,variou:2,venv:2,version:2,vertic:2,via:2,villeurbann:1,virtual:[],vise:[],vivien:[0,1],vlide:2,voi:[],voici:[],voltag:2,voltmet:2,vou:[],wai:2,watch:2,weaker:2,websit:2,welcom:1,well:2,were:2,when:2,where:2,which:2,whose:2,width:[],willing:1,window:2,wire:2,within:2,without:2,wjwzhv1v3pk:2,would:2,write:2,www:2,x_n:[],yannick:[0,1],you:2,your:2,youtub:2},titles:["OHMPI: Open source and open hardware resitivity-meter","<strong>OhmPi project</strong>","OhmPi V 1.01 (limited to 32 electrodes)"],titleterms:{IDE:2,The:2,activ:2,assembl:2,bienvenu:[],board:2,card:2,center:0,cett:[],configur:2,connect:2,construct:[],current:2,data:2,descript:2,developp:[],document:0,electr:2,electrod:2,environn:2,formul:[],four:2,frist:2,hardwar:0,imag:[],implement:2,implent:2,inastal:[],indic:[],initi:2,inject:2,instal:2,instruct:2,introduct:1,lien:[],limit:2,massembl:[],measur:2,mesur:2,meter:0,modif:[],multiplex:2,ohmpi:[0,1,2],onli:2,open:0,openalea:[],oper:2,packag:2,page:[],paramet:2,philosophi:2,preliminari:2,procedur:2,project:1,python:2,rapberri:2,raspberri:2,resist:2,resit:0,run:[],second:[],sourc:0,startup:2,step:[],summari:0,sur:[],tabl:[],technic:2,text:[],thonni:2,virtual:2,welcom:[]}})
\ No newline at end of file
......@@ -44,9 +44,9 @@ OS installation
The first step is to start up the Raspberry Pi board, including installation of an OS (operating system).
For this step, the installation instructions are well described on the Raspberry website
1- Watch the vidéo "how to set up your raspberry Pi" (https://www.youtube.com/watch?v=wjWZhV1v3Pk)
1. Watch the vidéo "how to set up your raspberry Pi" (https://www.youtube.com/watch?v=wjWZhV1v3Pk)
2- The authors recommend installing the latest stable and complete version of Raspbian by using NOOBS (a simple-to-use operating system installer).
2. The authors recommend installing the latest stable and complete version of Raspbian by using NOOBS (a simple-to-use operating system installer).
.. note::
All the development tests were performed on Raspberry Pi 3 Model B, we used the following version of Raspbian:
......@@ -64,6 +64,36 @@ For this step, the installation instructions are well described on the Raspberry
Once the OS has been installed, **1-wire, spi and GPIO remote option** must be deactivated via the Raspbian GUI settings menu. Failure to carry out this task may cause damage to the relay shield cards during measurements.
3. When the relays are connected to the GPIO, make sure that all the GPIOs are in the low position when the raspberry starts up. If not, the relays will activate unexpectedly.
To ensure that the GPIOs are in Low position, you will need to modify the /boot/config.txt file.
Run the terminal, and write
.. code-block:: python
cd /boot/
4. Open config.txt with GNU nano editor
.. code-block:: python
sudo nano config.txt
5. At the end of the file write :
.. code-block:: python
gpio=8=op,dl
gpio=7=op,dl
6. Press Ctrl +O to save the modifications and press enter
7. Press Ctrl +x to escap and return to the terminal
8. Close the terminal
Virtual Environnement and packages
==================================
......
Supports Markdown
0% or .
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment