Skip to content
GitLab
Commit 2ef49fd7 authored by Remi Clement's avatar Remi Clement
Browse files

update step 4 of Ohmpi V 2.00

parent 4a33b51d
master 144-create-testing-framework-for-tests-automation EGU23 MB.2024.ter_restored MUX_board_v2024 Refactor_mb_2023 battery_charger board_v4 code_refactor dev/dummy mqtt update_V2023 v2024_rc v2025_alpha v2024.0.34 v2024.0.33 v2024.0.32 v2024.0.31 v2024.0.30 v2024.0.29 v2024.0.28 v2024.0.27 v2024.0.26 v2024.0.25 v2024.0.24 v2024.0.23 v2024.0.22 v2024.0.21 v2024.0.20 v2024.0.19 v2024.0.18 v2024.0.17 v2024.0.16 v2024.0.15 v2024.0.14 v2024.0.13 v2024.0.12 v2024.0.11 v2024.0.10 v2024.0.9 v2024.0.8 v2024.0.7 v2024.0.0 v2023.0.1 v2023.0.0 archives/mqtt
No related merge requests found
Hide whitespace changes
Inline Side-by-side
Showing
with 46 additions and 2 deletions
+46 -2
doc/source/Ohmpi_V2_00/V2_00_step_04.rst
+ 46
− 2
View file @ 2ef49fd7
...@@ -17,11 +17,55 @@ ...@@ -17,11 +17,55 @@
+--------+------------------------------------------------------------+ +--------+------------------------------------------------------------+
| | .. image:: step_n_4/step_4_2.jpg | | | .. image:: step_n_4/step_4_2.jpg |
| 1 +------------------------------------------------------------+ | 2 +------------------------------------------------------------+
| |Crimp the ribbon cable on the corresponding idc connector | | |Crimp the ribbon cable on the corresponding idc connector |
| |with a suitable clamp. Pay attention to the direction of the| | |with a suitable clamp. Pay attention to the direction of the|
| |cables. Unbalanced IDC connector. The ribbon cable must be | | |cables. Unbalanced IDC connector. The ribbon cable must be |
| |perpendicular to the connector. | | |perpendicular to the connector. |
+--------+------------------------------------------------------------+ +--------+------------------------------------------------------------+
.. table::
\ No newline at end of file :align: center
+--------+------------------------------------------------------------+
| | .. image:: step_n_4/step_4_3.jpg |
| 3 +------------------------------------------------------------+
| |Example of IDC connector mounting. The wires should run as |
| |perpendicular as possible to the IDC connector. |
+--------+------------------------------------------------------------+
.. table::
:align: center
+--------+------------------------------------------------------------+
| | .. image:: step_n_4/step_4_4.jpg |
| 4 +------------------------------------------------------------+
| |Same for a 6 wires ribbon cable of 1 m length. |
| | |
+--------+------------------------------------------------------------+
.. table::
:align: center
+--------+------------------------------------------------------------+
| | .. image:: step_n_4/step_4_5.jpg |
| 5 +------------------------------------------------------------+
| |Cut the ribbon cable flush with the IDC connector. |
| | |
+--------+------------------------------------------------------------+
.. table::
:align: center
+--------+------------------------------------------------------------+
| | .. image:: step_n_4/step_4_6.jpg |
| 6 +------------------------------------------------------------+
| |Position 9 spacers above the MUX board, and 9 spacers below.|
| | |
+ +------------------------------------------------------------+
| | .. image:: step_n_4/step_4_7.jpg |
| +------------------------------------------------------------+
| |Profile view for mounting the spacers above and below. |
| | |
+--------+------------------------------------------------------------+
\ No newline at end of file
Supports Markdown
0% or .
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment